Author Topic: Whirlpool washer spins only after opening lid (Read 7866 times)

Jim214 · « **on:** August 14, 2011, 01:42:40 PM »

My WP washer spins only after I open the lid. Pump is working. Just had the trans & clutch replaced recently.

Model LSQ9549LW0

Please help. Thanks...

AJ · « **Reply #1 on:** August 14, 2011, 03:00:53 PM »

Your timer is bad. The time has a built in pause before it goes into spin. This pause stops the motor and lets the transmission shift into the spin mode.

By lifting up the lid you are creating the pause manually by stopping the motor.

I see this problem all the time. I looked up the model number of your washer and the timer it uses is part # 3951702 Timer, AP3020314

Jim214 · « **Reply #2 on:** August 14, 2011, 03:15:14 PM »

Thanks AJ. Do you know if there are any instructions out there to R&R the timer?

AJ · « **Reply #3 on:** August 14, 2011, 03:19:23 PM »

AJ · « **Reply #4 on:** August 14, 2011, 03:25:13 PM »

Here is a good video that shows you how to replace the type of timer you have in your washer. The timer can not be repair so it will have to be replaced.

http://www.youtube.com/watch?v=OPTORJrpHxM

Jim214 · « **Reply #5 on:** August 14, 2011, 05:07:31 PM »

Thanks AJ. R&R= remove & replace.

Jim214 · « **Reply #6 on:** August 17, 2011, 07:24:40 AM »

I got the new timer & installed it...still not spinning until I open the lid. Any plan B?

whirlpooltech · « **Reply #7 on:** August 17, 2011, 07:33:50 AM »

Quote from: Jim214 on August 17, 2011, 07:24:40 AM

I got the new timer & installed it...still not spinning until I open the lid. Any plan B?

When you open the lid, or when you open and then close the lid?

I think AJ was thinking it started spinning after you open and then closed the lid again as was I when I first read your post.

If in fact the washer starts spinning when you open the lid, so it's spinning with the lid open then you have a bad lid switch.

Jim214 · « **Reply #8 on:** August 17, 2011, 07:45:37 AM »

No, it's when I open & close it. It then starts to spin.

tgoods · « **Reply #9 on:** August 17, 2011, 09:21:55 AM »

Lid switch, 8054980.

Jim214 · « **Reply #10 on:** August 17, 2011, 09:32:10 AM »

Ok, to install it do I have to remove the shell? Is there any instructions out there?
Should I return the timer that I already installed?
Thanks

JWWebster · « **Reply #11 on:** August 17, 2011, 09:52:38 AM »

How to get into the machine

Direct Drive lid switch replacement

Everythang you ever wanted to know about your machine

AJ · « **Reply #12 on:** August 17, 2011, 09:56:18 AM »

Quote from: Jim214 on August 17, 2011, 09:32:10 AM

Ok, to install it do I have to remove the shell? Is there any instructions out there?
Should I return the timer that I already installed?
Thanks

The type of lid switch you have can be access and replace by simply lifting up the control counsel like you did to replace the timer. The switch is located on top the cabinet so the cabinet does not have to be removed in this case.

Get Answers to your Appliance Repair Questions

ApplianceJunk.com

Appliance Repair Forum