Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   AppliancePartsPros 

Author Topic: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?  (Read 13007 times)

Offline A-Dub

  • VIP Member
  • Member Since: Aug 2014
  • Posts: 8

Hello all-

I am new here and have a problem.

I have a Maytag MVWX500XW2 that is a couple months out of warranty...

Anyway, I have done some of the diagnostic tests and researched the issue a good bit.

When it performs the automatic test, it usually fails when it gets to "Motor Spins" test.  I get a "lid lock fault" error.  (The machine stops and lid lock light flashes)  I believe the lid lock fault was also occasionally occurring earlier in the wash cycle when in normal use.

My question is this: Is the problem likely the lid latch (the lock mechanically seems to work since it locks and unlocks at times) or would it be more likely to be the main board not able to detect the lid is locked when going to spin?

Any insight would be greatly appreciated!

-Andrew

Offline Jdm

  • Technician
  • Member Since: May 2011
  • Posts: 145
  • Country: us
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #1 on: August 14, 2014, 08:44:22 AM »
Lid lock light will flash when the machine itself has a problem. You need to put it in a diagnostic test & get the fault codes first. The manual is under the top on the front of the cabinet.
It's not the legacy you leave, it's the lives you impact

Offline A-Dub

  • VIP Member
  • Member Since: Aug 2014
  • Posts: 8
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #2 on: August 14, 2014, 08:52:06 AM »
Jdm-

Ok I have performed the automatic test and it stops at the motor spins test.

Do I then need to perform the fault/error code procedure after performing the automatic test in diagnostic mode?


Offline Jdm

  • Technician
  • Member Since: May 2011
  • Posts: 145
  • Country: us
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #3 on: August 14, 2014, 08:53:57 AM »
Fault codes will help
It's not the legacy you leave, it's the lives you impact

Offline A-Dub

  • VIP Member
  • Member Since: Aug 2014
  • Posts: 8
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #4 on: August 14, 2014, 09:01:07 AM »
Ok I will try that when I get home.

I wasn't sure if the fault/error codes were saved/generated after a diagnostic test or in regular use.

Thank you

Offline LowSL2

  • Technician
  • Member Since: Dec 2011
  • Posts: 1238
  • Country: us
  • My knees hurt
    • Buy me a beer through paypal
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #5 on: August 14, 2014, 09:52:14 AM »
It stores fault codes from normal use and from diagnostic tests. Read the section on your tech sheet on how to retrieve fault codes and tell us what is stored.  Then we can help you out.
LowSL2
15+ Years of Professional Appliance Repair Experience
Former $ears/a$e tech

Offline rockinrobin

  • Technician
  • Member Since: Sep 2011
  • Posts: 459
  • Country: us
    • Buy me a beer through paypal
    • Ransom Mobile Appliance Repair Service
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #6 on: August 14, 2014, 10:54:01 AM »
Ok I will try that when I get home.

I wasn't sure if the fault/error codes were saved/generated after a diagnostic test or in regular use.

Thank you
Make sure the Basket rotates freely by hand both direction's, if it doesn't then you may have something stuck between the Inner Basket and Outer Tub.
When you run the Fault Code Display Mode (after you Activate the Service Diagnostic Test Mode), the first code is the most recent (be sure to write them down in order).
Also, be sure the nut is tight on the big belt pulley (located in the bottom center underneath the unit, remove plastic cover shield to tighten the nut).
Afterwards, run the Manual Test for Agitation & Spin Mode (lift the top panel during test to see if it will try to Agitate and/or Spin).
If the Fault/Error Code is either F7E1 & F7E5 (or both), the most common part that fails on this unit is the Shifter/Actuator (p/n W10006355).
After replacing any electrical parts, always run the Calibration Test so the Washer works properly.
View the video (below) from YouTube to help you get into Diagnostic Mode & Fault Code Display Mode:


« Last Edit: August 14, 2014, 11:05:31 AM by rockinrobin »

Offline A-Dub

  • VIP Member
  • Member Since: Aug 2014
  • Posts: 8
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #7 on: August 14, 2014, 11:45:14 AM »
LowSL2- Ok I will run the fault codes and let you guys know what they say.

rockinrobin- I do remember that when I tried to turn the basket it only would turn a little ways in either direction before it would "pull back".  I could not turn or spin it on its own.

Thanks

Offline rockinrobin

  • Technician
  • Member Since: Sep 2011
  • Posts: 459
  • Country: us
    • Buy me a beer through paypal
    • Ransom Mobile Appliance Repair Service
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #8 on: August 14, 2014, 12:58:53 PM »
LowSL2- Ok I will run the fault codes and let you guys know what they say.

rockinrobin- I do remember that when I tried to turn the basket it only would turn a little ways in either direction before it would "pull back".  I could not turn or spin it on its own.

Thanks
Check for Fault Code's first, be sure big pulley nut is tight then run the Manual Test Mode for Agitate & Spin (lift Top Panel during Test to view Agitator & Basket movement).
Look underneath the Washer to see if there's any oily residue on any part's mounted under the Tub.
If yes, then you probably have a bad Transmission/Gearcase.
If no, try to manually rotate the big pulley (mounted under Transmission) in both direction's (before rotating be sure pulley nut is tight).
If you cannot rotate the big pulley either direction, then remove Basket to see if there's anything stuck between Basket & Tub (view repair manual for disassembly procedure).
Download the Repair Manual below to help with troubleshooting (link also has a few troubleshooting video's for this type of unit)
http://appliancejunk.com/forums/index.php?action=downloads;sa=view;down=434
 
 

Offline A-Dub

  • VIP Member
  • Member Since: Aug 2014
  • Posts: 8
Re: Maytag Bravos Won't Spin: Lid Lock Fail or Main Board/other issue?
« Reply #9 on: August 14, 2014, 07:38:48 PM »
The fault code is F7E1

 

Maytag Bravos new main control board

Started by Dickens

Replies: 2
Views: 1319
Last post June 18, 2015, 11:40:52 AM
by ApplianceAssista
Maytag Bravos (VMW) - Intermittent spin & lid lock issues?

Started by Low Efficiency

Replies: 1
Views: 527
Last post January 01, 2017, 09:54:07 PM
by schleven
Maytag Neptune Spin Problem/Contoller board not burnt

Started by sdocsmith

Replies: 3
Views: 4051
Last post January 08, 2009, 02:52:28 PM
by whirlpooltech
Maytag Neptune does not spin - replaced control board looks OK

Started by sgwfromBG

Replies: 3
Views: 4301
Last post October 01, 2009, 06:06:32 PM
by sgwfromBG
LG Giant C Washer - No power - Replaced Main Board - Again same issue

Started by mblover

Replies: 4
Views: 3377
Last post July 08, 2014, 10:35:29 AM
by wildimaginations
Maytag Bravos X won't spin or agitate correctly

Started by rossocarne

Replies: 16
Views: 15668
Last post April 06, 2015, 11:40:46 PM
by afterblast