ApplianceJunk.com

Forum Index => Chit Chat => Topic started by: jbneedshelp on October 10, 2013, 05:08:08 PM

Title: coin opps whirlpool dryer i want to extend the dry time, can't figure out how
Post by: jbneedshelp on October 10, 2013, 05:08:08 PM
can't figure out how to extend the timer on the coin opp for more time it is currently 30 min i'd like to go to 50 or 60 min
Title: Re: coin opps whirlpool dryer i want to extend the dry time, can't figure out how
Post by: dab147315 on October 10, 2013, 05:36:16 PM

There should be these cam inside by timer and if you have customer manual it will tell you which one to use.
Title: Re: coin opps whirlpool dryer i want to extend the dry time, can't figure out how
Post by: dab147315 on October 10, 2013, 05:55:27 PM
http://www.appliancepartspros.com/whirlpool-timing-cam-343777-ap3133938.html (http://click.linksynergy.com/fs-bin/click?id=omv7WULuxaw&subid=0&offerid=225193.1&type=10&tmpid=2111&RD_PARM1=http&RD_PARM2=%253A%252F%252Fwww.appliancepartspros&RD_PARM3=.com%252Fwhirlpool-timing-cam-343777-ap3133938.html) They look like this and there should be 3 inside by the timer.They come with the dryer and you put in the 60 minute one and i don't remember which one it is .http://www.appliancepartspros.com/whirlpool-timing-cam-3387974-ap3083148.html (http://click.linksynergy.com/fs-bin/click?id=omv7WULuxaw&subid=0&offerid=225193.1&type=10&tmpid=2111&RD_PARM1=http&RD_PARM2=%253A%252F%252Fwww.appliancepartspros&RD_PARM3=.com%252Fwhirlpool-timing-cam-3387974-ap3083148.html) if it the same model it maybe this one.
Title: Re: coin opps whirlpool dryer i want to extend the dry time, can't figure out how
Post by: jbneedshelp on October 11, 2013, 05:30:23 AM
thanks for the info it was a used machine so there were no parts with it, i have ordered the part and can't thank you enough
Jim
Title: Re: coin opps whirlpool dryer i want to extend the dry time, can't figure out how
Post by: Wedgeman55 on October 19, 2013, 05:30:32 PM
my specialty...........................  Here's how you do it.    #1,  if you now have 30 minutes,  count the number of pins on the cam.   Most timer clocks are either 60 or 180.   (old ones I used to service went to 240 minutes).     If you have 2 pegs on it,   take the cam off and grind or chop off one of the pegs.    This will give you 1 peg, = 60 minutes.      If you have a 180 minute clock,  then to get 30 minutes you would need a 6 peg wheel.    If you want an hour,   clip every other peg to get a 3 peg wheel.   You get the drift.             Most come from factory set for 45 minutes.   They have a 4 peg wheel and a 180 minute clock on the whirlpools.    30 minutes is not a factory setting.    If you are in doubt,  look at the timer motor on the timer.     It usually tells you the clock time.    (180,  60,  30)  etc.   Good luck.